DI-A126
DI_a126_limpModefaultsModel3only
Was bedeutet DI-A126?
Tesla Alarm-Code im Antriebswechselrichter-Modul (DI). Drive Inverter Warning: No functional heatsink temperature sensors Drive Inverter Warning: Phase current imbalance Imbalanced phase currents detected. See payload signals for reason of trigger Reason of trigger is no longer present Drive Inverter Temp Estimator Implausible Drive Inverter Warning: Unit limp mode triggered Abnormal condition detected within drive unit subsystem. Look at limpReason in alert for exact trigger. Drive Inverter Warning: Motor encoder error detected in hardware Drive Inverter Warning: Oil pump failure Loss of communication or power to oil pump, or persistent oil pump motor stall or fault occurred Clears at the start of a drive cycle, if set condition is not present anymore Initiates reduced drive unit performance and a speed limit on the vehicle, due to reduced gear lubrication and motor cooling Drive Inverter Warning: Motor over speed Drive Inverter Warning: Power stage current observer complete Drive Inverter Warning: LIN communication error Drive Inverter Warning: Battery under voltage HV bus voltage (refer to busVoltage) drops below lower voltage threshold (refer to busHighLimit) HV bus voltage rises back above lower voltage threshold Drive Inverter Warning: Active damping error Drive Inverter Warning: Ambient over temperature Ambient temperature (refer to pcbTemp) exceeds upper temperature threshold Ambient temperature drops below upper temperature threshold Drive Inverter Warning: Rotor flux and offset learning routine is in progress Drive Inverter Warning: Phase B peak over current detected in software Drive Inverter Warning: Power Stage Not Ready Triggers ODIN service to upload log buffer Drive Inverter Warning: Heatsink under temperature Heatsink temperature (refer to heatsinkTemp) drops below lower temperature threshold Heatsink temperature rises above lower temperature threshold Drive Inverter Warning: Ambient sensor bad Abnormal temperature measurements from ambient sensor Ambient sensor returns to rational temperature measurements Unable to monitor ambient sensor temperature Drive Inverter Warning: Phase C peak over current detected in hardware Diagnsotic Alert: Irrational rotor offset detected Rotor offset mean estimator is above minimum rationality threshold at very low absolute torque outputs Rotor offset mean estimator falls below minimum rationality threshold Diagnostic alert data only, may indicate reduction in torque or excess heat accuracy Drive Inverter Warning: DC bus disconnected Drive Inverter Warning: Active discharge is on but bus voltage remains high Bus voltage is high while active discharge is ON Bus voltage is low or active discharge is off Potentially exposed high voltage
Originale Beschreibung
Drive Inverter Warning: No functional heatsink temperature sensors Drive Inverter Warning: Phase current imbalance Imbalanced phase currents detected. See payload signals for reason of trigger Reason of trigger is no longer present Drive Inverter Temp Estimator Implausible Drive Inverter Warning: Unit limp mode triggered Abnormal condition detected within drive unit subsystem. Look at limpReason in alert for exact trigger. Drive Inverter Warning: Motor encoder error detected in hardware Drive Inverter Warning: Oil pump failure Loss of communication or power to oil pump, or persistent oil pump motor stall or fault occurred Clears at the start of a drive cycle, if set condition is not present anymore Initiates reduced drive unit performance and a speed limit on the vehicle, due to reduced gear lubrication and motor cooling Drive Inverter Warning: Motor over speed Drive Inverter Warning: Power stage current observer complete Drive Inverter Warning: LIN communication error Drive Inverter Warning: Battery under voltage HV bus voltage (refer to busVoltage) drops below lower voltage threshold (refer to busHighLimit) HV bus voltage rises back above lower voltage threshold Drive Inverter Warning: Active damping error Drive Inverter Warning: Ambient over temperature Ambient temperature (refer to pcbTemp) exceeds upper temperature threshold Ambient temperature drops below upper temperature threshold Drive Inverter Warning: Rotor flux and offset learning routine is in progress Drive Inverter Warning: Phase B peak over current detected in software Drive Inverter Warning: Power Stage Not Ready Triggers ODIN service to upload log buffer Drive Inverter Warning: Heatsink under temperature Heatsink temperature (refer to heatsinkTemp) drops below lower temperature threshold Heatsink temperature rises above lower temperature threshold Drive Inverter Warning: Ambient sensor bad Abnormal temperature measurements from ambient sensor Ambient sensor returns to rational temperature measurements Unable to monitor ambient sensor temperature Drive Inverter Warning: Phase C peak over current detected in hardware Diagnsotic Alert: Irrational rotor offset detected Rotor offset mean estimator is above minimum rationality threshold at very low absolute torque outputs Rotor offset mean estimator falls below minimum rationality threshold Diagnostic alert data only, may indicate reduction in torque or excess heat accuracy Drive Inverter Warning: DC bus disconnected Drive Inverter Warning: Active discharge is on but bus voltage remains high Bus voltage is high while active discharge is ON Bus voltage is low or active discharge is off Potentially exposed high voltage
Schweregrad-Hinweise
DI-A126 ist ein Alarm im Drive Inverter-System. Es ist im Allgemeinen sicher, weiterzufahren, aber lassen Sie es beim nächsten geplanten Service überprüfen.